Products Archive - Glide Air Deflector System

Our Products

SGADS14 PKG for Harley Davidson® Street Glide models 2014 and Up

$69.95

SGADS + GADS LT14 The SGADS14-PKG is a combination package of 2 different GADS products put together at a discounted price sent in a single box. As a package, they work as a set to deliver a better, more comfortable riding experience at a lower overall price. *Not compatible with factory hard lower fairings (does work with soft lowers). Installation Instructions View Colors
Installation Instructions View Colors

SGADS

Installation Instructions for Street Glide models through 2013
The fairing shell will have to be removed to enable access to the plug end at the end of the turn signal wires. The deflectors install by removing the front turn signals, threading the fixture into the deflector while routing the wire to the turn signal through the small pre-drilled hole in the deflector then reinstalling the two pieces back onto the side of the down tubes. The opening for the turn signal should have a consistent reveal around the lens and fixture. There is a small amount of adjustment available to center the fixture in the opening. Reroute the turnsignal wire back to the factory connection. Test the turn signals prior to re-installation of the fairing shell ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

GADS LT14

Touring Platform 2014 And Up Lower Triple Tree Deflector
Remove the protective coating. Fasten the GADSLT14 to the lower triple tree, using the bolts that hold the fork slider cover. Apply a small amount of thread lock to bolts and torque to a snug fit Do not over tighten (DOES NOT FIT TRI-GLIDE)

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS Vanderhall Venice Wind Deflectors

$69.45
SKU: GADSVDV

Designed and manufactured specifically for the Vanderhall Venice.

Easy Installation Complete with all required hardware.

Allows a quieter more comfortable ride with much less turbulence.

Smooth lines and curves complement the Venice body style.

Created with a light smoke PolyCarbonate that closely matches the Venice Windshield.

The polycarbonate is a flexible product that is very impact resistant.

MADE IN THE USA Installation Instructions
Add to cart Details
EGADS-PKG for Harley Davidson® Electra Glide 2014 and up

$66.50
EGADS-PKG = EGADS + GADSLT14 (varies - compatible with the 2 piece spot lamp bracket DOES work with hard lowers, not compatible with Street Glide turn signal bracket) The EGADS-PKG is a combination package of 2 different GADS products put together at a discounted price, sent in a single package. As a package they work as a set to deliver a better, more comfortable riding experience at a lower overall price. Installation Instructions View Colors

EGADS by GADS

Installation instructions for cast aluminum brackets

Various Electra-Glide 2013 and up

Package includes,4 spacers, 4 stainless bolts, 4 stainless washers, 2 deflectors
EXTREMELY IMPORTANT: Finish first side before beginning the second!!

Start by covering the front fender and lowers

Remove the spot lamp bracket (rest the bracket on the covered lowers and crash bar, use caution with the electrical connection)

Remove original mounting studs

Remove the protective film from deflectors

Install washers on bolts

While holding the bracket, nest the deflector around it aligning holes

Put the spacer in the top pocket of the bracket while aligning holes

Install top bolt with washer through bracket, spacer and deflector then loosely thread bolt into place. (You may have to move the fairing around a little to align holes)

Make sure the electrical plug is tucked in behind bracket then repeat steps with the lower bolt and spacer

Tighten bolts to manufacture requirements

move to the other side and repeat

Proudly made in the U.S.A. www.glideairdeflectorsystem.com Thank you for your support MADE IN THE U.S.A.

GADS LT14

Touring Platform 2014 And Up Lower Triple Tree Deflector
Remove the protective coating. Fasten the GADSLT14 to the lower triple tree, using the bolts that hold the fork slider cover. Apply a small amount of thread lock to bolts and torque to a snug fit Do not over tighten (DOES NOT FIT TRI-GLIDE)
Select options This product has multiple variants. The options may be chosen on the product page Details
SGADS PKG for Harley Davidson® Street Glide Models through 2013

$64.95

SGADS + GADS LTTD The SGADS-PKG is a combination package of 2 different GADS products put together at a discounted price sent in a single box. As a package, they work as a set to deliver a better, more comfortable riding experience at a lower overall price. *Does not fit Street Glide models 2014 and up. *Not compatible with factory hard lower fairings (does work with soft lowers). Installation Instructions View Colors
Installation Instructions View Colors

SGADS

Installation Instructions for Street Glide models through 2013
The fairing shell will have to be removed to enable access to the plug end at the end of the turn signal wires. The deflectors install by removing the front turn signals, threading the fixture into the deflector while routing the wire to the turn signal through the small pre-drilled hole in the deflector then reinstalling the two pieces back onto the side of the down tubes. The opening for the turn signal should have a consistent reveal around the lens and fixture. There is a small amount of adjustment available to center the fixture in the opening. Reroute the turnsignal wire back to the factory connection. Test the turn signals prior to re-installation of the fairing shell ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

GADS LTTD

GADS Lower Triple Tree Deflector

This deflector installs to most touring platform H-D motorcycles through 2013
If you look at the back edge of your lower triple tree and see 3 little plastic plugs or holes this is where your deflector mounts The bolts that hold the GADSLTTD on are 1/4”X20 tpi. The triple tree is pre-drilled and tapped to accept the included bolts. If there is any resistance when screwing in the bolts you need to chase the threads with a 1/4”-20 tap to remove any obstruction on the threads (paint,rust,etc.) GADS is a small cottage industry Thank you for your support Made in the U.S.A.

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS Vanderhall Carmel Wind Deflectors

$64.50
Designed and manufactured specifically for the Vanderhall Carmel.

Styled to enhance the smooth lines of your beautiful machine.

Easy Installation Complete with all required hardware.

Allows a quieter more comfortable ride with much less turbulence.

Can be used with or without the hardtop.

Created with a light smoke Poly Carbonate that closely matches the Carmel Windshield.

The poly carbonate is a flexible product that is very impact resistant.

MADE IN THE USA Installation Instructions
Add to cart Details
GADS-PKGRGB for Harley Davidson® Road Glide 2015 and up

$57.49

GADS-PKGRGB = GADSRGB + GADSLT14 (does not work with hard lowers) The GADS-PKGRGB is a combination package of 2 different GADS products put together at a discounted price, sent in a single box. As a package they work as a set to deliver a better, more comfortable riding experience at a lower overall price. Installation Instructions

GADS RGB

2015 AND UP ROAD GLIDE
Installation of the GADSRGB is very easy Note: If your motorcycle has OEM Willie Wings you may want to either trim back the portion that hangs below the fairing or add washers to shim the GADSRGB for clearance. • Remove the gray protective covering on the deflectors. • Locate the enclosed package with the four 1/4”X20 tpi bolts and eight washers. • Locate the threaded inserts on the bottom of the fairing in front of and behind the turn signals, this is where you will install the GADSRGB. • The deflector mounts inboard of the turn signal, hangs down and flares out in front of your knee. • Place a washer on each side of the deflector. 4 per deflector. Hold the GADSRGB in place and install the bolts to a snug fit. (DO NOT OVER TIGHTEN) We are a small cottage Industry Thank you for your support GlideAirDeflectorSystem.com MADE IN THE U.S.A.

GADS LT14

Touring Platform 2014 And Up Lower Triple Tree Deflector
Remove the protective coating. Fasten the GADSLT14 to the lower triple tree, using the bolts that hold the fork slider cover. Apply a small amount of thread lock to bolts and torque to a snug fit Do not over tighten (DOES NOT FIT TRI-GLIDE)

Add to cart Details
GADS-PKG003 for Harley Davidson® Electra Glide through 2013, Various Road King Models

$55.95

GADS-PKG003 = GADS003 + GADSLTTD (not compatible with the Cast 2 piece spotlamp / turnsignal brackets) The GADS-PKG003 is a combination package of 2 different GADS products put together at a discounted price, sent in a single package. As a package they work as a set to deliver a better, more comfortable riding experience at a lower overall price. *The GADS003 normally will not fit the cvo regardless of year, they will usually require the EGADS. Look at the pictures to decide. Please contact the seller to help verify if necessary. Installation Instructions View Colors

GADS003

Electra Glide models through 2013, Road Kings and Freewheelers Through Current Models
GADS003 are very easy to install. The GADS003 mount using the bolts that come out of the triple tree of the motorcycle. On a Road King these are the bolts that hold the windshield, and or the spot lamp bracket. On an Electra Glide these are the bolts that hold the spot lamp bracket. The scallop goes up, the angle of the deflector goes out and towards the rear of the motorcycle. Simply remove one bolt or nut at a time, loosely reinstall the nut or bolt then repeat the procedure with the second nut or bolt. You will have to bend the GADS003 to access the hardware but don’t let that bother you, the GADS003 are extremely flexible and will simply spring back into place. When you have the nuts or bolts back into place, torque to specifications. Do not over tighten as this may cause stress fractures ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

GADS LTTD

GADS Lower Triple Tree Deflector

This deflector installs to most touring platform H-D motorcycles through 2013
If you look at the back edge of your lower triple tree and see 3 little plastic plugs or holes this is where your deflector mounts The bolts that hold the the GADSLTTD on are 1/4”X20 tpi. The triple tree is pre-drilled and tapped to accept the included bolts. If there is any resistance when screwing in the bolts you need to chase the threads with a 1/4”-20 tap to remove any obstruction on the threads (paint,rust,etc.) GADS is a small cottage industry Thank you for your support Made in the U.S.A.

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS-PKG001 for Harley Davidson® Road Glide 2004 – 2013

$55.95
GADS-PKG001 = GADS001 + GADSLTTD The GADS-PKG001 is a combination package of 2 different GADS products put together at a discounted price sent in a single box. As a package, they work as a set to deliver a better, more comfortable riding experience at a lower overall price. Installation Instructions View Colors

GADS001

2004 -2013 RoadGlide
GADS are created using virtually indestructible polycarbonate. GADS have a mounting system that uses the turn signal mounts to hold the deflector in place. They sit between the mounting bracket and the inner fairing, virtually invisible from the outside of the fairing. The top of the mounting flange has a hole and a notch, allowing for adjustment. The top of the flange is horizontal and sits toward the center line of the motorcycle. The notch is for the rear bolt and the wiring. Keep the wiring in the notch, do not pinch the wiring. The hole is for the front mounting stud.

Remove protective film from GADS.

Cover the front fender with a towel to avoid scratches or dings.

Pick a side to install the GADS on, then remove the nuts that hold the front turn signal on but do not remove the signal yet as there are wires that power the signal.

Pull the turn signal studs loose from the fairing but do not pull the wires out of the fairing.

Slide the hole in the front of the deflector mounting flange between the mounting bracket and the inner fairing aligning the three holes. (inner fairing, GADS, fairing support bracket)

Loosely install turn signal CAUTION: DO NOT PINCH WIRING

The notch allows for a small amount of adjustment, pivot the deflectors toward the crash bar, recheck wiring, then tighten to torque spec. do not over tighten if installing GADS002 in front of lowers, install so the ploycarbonate cannot come into contact with the paint. GADS will bend a small amount under a wind load.

Move to the other side and repeat

GADS is a small cottage industry Thank you for your support Made in the U.S.A.

GADS LTTD

GADS Lower Triple Tree Deflector

This deflector installs to most touring platform H-D motorcycles through 2013
If you look at the back edge of your lower triple tree and see 3 little plastic plugs or holes this is where your deflector mounts The bolts that hold the the GADSLTTD on are 1/4”X20 tpi. The triple tree is pre-drilled and tapped to accept the included bolts. If there is any resistance when screwing in the bolts you need to chase the threads with a 1/4”-20 tap to remove any obstruction on the threads (paint,rust,etc.) GADS is a small cottage industry Thank you for your support Made in the U.S.A.
Select options This product has multiple variants. The options may be chosen on the product page Details
SGADS14 for Harley Davidson® Street Glide Models 2014 and Up

$54.95

SGADS is a deflector for street glides using the standard fork mount turn signal/ bracket system. This set of deflectors wrap around the turn signals on the front of the Street Glide rerouting much of turbulence around the rider. GADS deflectors are designed to relieve the worst of the perceived hammering turbulence experienced by the riders, but not totally move all of the air away from the rider, That is what cars are for. MADE IN THE USA *Not for Street Glide models before 2014. *Not compatible with factory hard lower fairings (does work with soft lowers). Installation Instructions View Colors

SGADS
Installation 2014 and up STREET GLIDE deflectors, (this requires the included hardware package) 4 stainless 5/16” bolts, 4 spacers, 4 washers Remove the turnsignal brackets, disconnect the small wiring connector, remove the studs set aside save and reuse the washers. The wiring plug for the signal fit through a 1” hole in the triple tree cover. Thread the wire through the corresponding hole in the deflector. Refasten the connection through the deflector to the wire on the back of the bracket. Put a washer on 2 bolts, fit through the turn signal bracket, install a spacer on the bolts, inside the brackets while not pinching the turn signal wires. Loosely install the deflector to the corresponding holes on the side of the triple tree. The deflector has some adjustment built in to center the turn signal in the opening. Check for fitment and pinched wiring as you tighten to specified in the service manual. Over tightening may result in stress fractures in the polycarbonate. ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS-PKG002 for Harley Davidson® Road Glide Ultra Models 2004 – 2013

$53.95
GADS-PKG001 = GADS001 + GADSLTTD (with hard lowers) The GADS-PKG002 is a combination package of 2 different GADS products put together at a discounted price sent in a single box. As a package they work as a set to deliver a better, more comfortable riding experience at a lower overall price. Installation Instructions View Colors

GADS002

2004 -2013 RoadGlide
GADS are created using virtually indestructible polycarbonate. GADS have a mounting system that uses the turn signal mounts to hold the deflector in place. They sit between the mounting bracket and the inner fairing, virtually invisible from the outside of the fairing. The top of the mounting flange has a hole and a notch, allowing for adjustment. The top of the flange is horizontal and sits toward the center line of the motorcycle. The notch is for the rear bolt and the wiring. Keep the wiring in the notch, do not pinch the wiring. The hole is for the front mounting stud.

Remove protective film from GADS.

Cover the front fender with a towel to avoid scratches or dings.

Pick a side to install the GADS on, then remove the nuts that hold the front turn signal on but do not remove the signal yet as there are wires that power the signal.

Pull the turn signal studs loose from the fairing but do not pull the wires out of the fairing.

Slide the hole in the front of the deflector mounting flange between the mounting bracket and the inner fairing aligning the three holes. (inner fairing, GADS, fairing support bracket)

Loosely install turn signal CAUTION: DO NOT PINCH WIRING

The notch allows for a small amount of adjustment, pivot the deflectors toward the crash bar, recheck wiring, then tighten to torque spec. do not over tighten if installing GADS002 in front of lowers, install so the ploycarbonate cannot come into contact with the paint. GADS will bend a small amount under a wind load.

Move to the other side and repeat

GADS is a small cottage industry Thank you for your support Made in the U.S.A.

GADS LTTD

GADS Lower Triple Tree Deflector

This deflector installs to most touring platform H-D motorcycles through 2013
If you look at the back edge of your lower triple tree and see 3 little plastic plugs or holes this is where your deflector mounts The bolts that hold the the GADSLTTD on are 1/4”X20 tpi. The triple tree is pre-drilled and tapped to accept the included bolts. If there is any resistance when screwing in the bolts you need to chase the threads with a 1/4”-20 tap to remove any obstruction on the threads (paint,rust,etc.) GADS is a small cottage industry Thank you for your support Made in the U.S.A.
Select options This product has multiple variants. The options may be chosen on the product page Details
SGADS for Harley Davidson® Street Glide Models through 2013

$49.95

SGADS is a deflector for street glides using the standard fork mount turn signal/ bracket system. This set of deflectors wrap around the turn signals on the front of the Street Glide rerouting much of turbulence around the rider. GADS deflectors are designed to relieve the worst of the perceived hammering turbulence experienced by the riders, but not totally move all of the air away from the rider, That is what cars are for. MADE IN THE USA *Does not fit Street Glide models 2014 and up. *Not compatible with factory hard lower fairings (does work with soft lowers). Installation Instructions View Colors

SGADS

Installation Instructions for Street Glide models through 2013
The fairing shell will have to be removed to enable access to the plug end at the end of the turn signal wires. The deflectors install by removing the front turn signals, threading the fixture into the deflector while routing the wire to the turn signal through the small pre-drilled hole in the deflector then reinstalling the two pieces back onto the side of the down tubes. The opening for the turn signal should have a consistent reveal around the lens and fixture. There is a small amount of adjustment available to center the fixture in the opening. Reroute the turnsignal wire back to the factory connection. Test the turn signals prior to re-installation of the fairing shell ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS EGADS for Harley Davidson® Electra Glide 2014 and up

$49.95
EGADS Electra Glide Air Deflector System - After many requests, we have developed an Air Deflector for the late model Harley-Davidson® Electra Glide using the cast spot lamp bracket. There is a cutout made to encompass the new spot lamp arm. Verify that your bike has the same spot lamp bracket shown in the picture. The EGADS is crafted using high quality, high impact Dark Smoke Polycarbonate Instructions and all hardware included Softens the wind and turbulence allowing you to hear your sound system. Works in conjunction with the GADS LTTD (Lower Triple Tree Deflector) MADE IN THE USA Installation Instructions View Colors

EGADS by GADS

Installation instructions for cast aluminum brackets

Various Electra-Glide 2013 and up

Package includes,4 spacers, 4 stainless bolts, 4 stainless washers, 2 deflectors
EXTREMELY IMPORTANT: Finish first side before beginning the second!!

Start by covering the front fender and lowers

Remove the spot lamp bracket (rest the bracket on the covered lowers and crash bar, use caution with the electrical connection)

Remove original mounting studs

Remove the protective film from deflectors

Install washers on bolts

While holding the bracket, nest the deflector around it aligning holes

Put the spacer in the top pocket of the bracket while aligning holes

Install top bolt with washer through bracket, spacer and deflector then loosely thread bolt into place. (You may have to move the fairing around a little to align holes)

Make sure the electrical plug is tucked in behind bracket then repeat steps with the lower bolt and spacer

Tighten bolts to manufacture requirements

move to the other side and repeat

Proudly made in the U.S.A. www.glideairdeflectorsystem.com Thank you for your support
Select options This product has multiple variants. The options may be chosen on the product page Details
GADS RGB for Harley Davidson® Road Glide 2015 and up

$41.49

The GADS RGB deflector is for Road Glide Custom 2015 models, but does not fit with lowers. GADS RGB comes with the required mounting bolts. The deflector mounts to threaded inserts already on the fairing. The GADS RGB is Dark Smoke polycarbonate. A combination package is also available to include the LT14. MADE IN THE USA Installation Instructions

GADS RGB

2015 AND UP ROAD GLIDE
Installation of the GADSRGB is very easy Note: If your motorcycle has OEM Willie Wings you may want to either trim back the portion that hangs below the fairing or add washers to shim the GADSRGB for clearance. • Remove the gray protective covering on the deflectors. • Locate the enclosed package with the four 1/4”X20 tpi bolts and eight washers. • Locate the threaded inserts on the bottom of the fairing in front of and behind the turn signals, this is where you will install the GADSRGB. • The deflector mounts inboard of the turn signal, hangs down and flares out in front of your knee. • Place a washer on each side of the deflector. 4 per deflector. Hold the GADSRGB in place and install the bolts to a snug fit. (DO NOT OVER TIGHTEN) We are a small cottage Industry Thank you for your support GlideAirDeflectorSystem.com MADE IN THE U.S.A.

Add to cart Details
GADS 003 for Harley Davidson® Electra Glide models through 2013, Road Kings and Freewheelers Through Current Models

$39.95

Easy installation using existing hardware. Redirects wind and turbulence that flows past the turn signals and up and over the gas tank. Fasten to the Spot Lamp Bracket mounting holes. Less disrupted air, smoother, quieter ride, and is inexpensive. MADE IN THE USA *Does not fit Street Glide models with stock turn signals, will also not fit with cast spotlight brackets. **The GADS003 normally will not fit the cvo regardless of year, they will usually require the EGADS. Look at the pictures to decide. Please contact the seller to help verify if necessary. Installation Instructions View Colors

GADS003

Electra Glide models through 2013, Road Kings and Freewheelers Through Current Models
GADS003 are very easy to install. The GADS003 mount using the bolts that come out of the triple tree of the motorcycle. On a Road King these are the bolts that hold the windshield, and or the spot lamp bracket. On an Electra Glide these are the bolts that hold the spot lamp bracket. The scallop goes up, the angle of the deflector goes out and towards the rear of the motorcycle. Simply remove one bolt or nut at a time, loosely reinstall the nut or bolt then repeat the procedure with the second nut or bolt. You will have to bend the GADS003 to access the hardware but don’t let that bother you, the GADS003 are extremely flexible and will simply spring back into place. When you have the nuts or bolts back into place, torque to specifications. Do not over tighten as this may cause stress fractures ___________________________________________________________________ All GADS deflectors are made of Polycarbonate plastic and are extremely durable, they should give you many years of trouble free service. Bob the GADS guy

Select options This product has multiple variants. The options may be chosen on the product page Details
GADS 001 for Harley Davidson® RoadGlide 2004 – 2013

$39.95
Glide Air Deflector System GADS is a new patent-pending approach to a comfortable RoadGlide experience. The turbulence that you feel on your face, chest and torso is dramatically reduced and redirected. Many RoadGlide owners spend lots of money buying expensive replacement windshields trying to find relief from the aggressive buffeting which is the effect caused by the RoadGlide Ultra fairing. Testing has proved, it is not the wind coming over the windshield beating you up, but the wind that comes up from under the sides of the fairing past the turn signals that is abusing the rider with extremely turbulent air. If you have ever put your feet on the top of your crash bars at highway speed you have some idea how well GADS will work for you. GADS mount to the fairing support bracket between the inner fairing and the fairing support bracket with a virtually invisible mounting system.(Will fit older RoadGlides if using updated turn signals and relocated upper fairing.) MADE IN THE USA Installation Instructions View Colors

GADS001

2004 -2013 RoadGlide
GADS are created using virtually indestructible polycarbonate. GADS have a mounting system that uses the turn signal mounts to hold the deflector in place. They sit between the mounting bracket and the inner fairing, virtually invisible from the outside of the fairing. The top of the mounting flange has a hole and a notch, allowing for adjustment. The top of the flange is horizontal and sits toward the center line of the motorcycle. The notch is for the rear bolt and the wiring. Keep the wiring in the notch, do not pinch the wiring. The hole is for the front mounting stud.

Remove protective film from GADS.

Cover the front fender with a towel to avoid scratches or dings.

Pick a side to install the GADS on, then remove the nuts that hold the front turn signal on but do not remove the signal yet as there are wires that power the signal.

Pull the turn signal studs loose from the fairing but do not pull the wires out of the fairing.

Slide the hole in the front of the deflector mounting flange between the mounting bracket and the inner fairing aligning the three holes. (inner fairing, GADS, fairing support bracket)

Loosely install turn signal CAUTION: DO NOT PINCH WIRING

The notch allows for a small amount of adjustment, pivot the deflectors toward the crash bar, recheck wiring, then tighten to torque spec. do not over tighten if installing GADS002 in front of lowers, install so the ploycarbonate cannot come into contact with the paint. GADS will bend a small amount under a wind load.

Move to the other side and repeat

GADS is a small cottage industry Thank you for your support Made in the U.S.A.
Select options This product has multiple variants. The options may be chosen on the product page Details
GADS 002 for Harley Davidson® RoadGlide 2004 – 2013

$37.95
Glide Air Deflector System GADS is a new patent pending approach to a comfortable RoadGlide experience. The turbulence that you feel on your face, chest and torso is dramatically reduced and redirected. Many RoadGlide owners spend lots of money buying expensive replacement windshields trying to find relief from the aggressive buffeting which is the effect caused by the RoadGlide Ultra fairing. Testing has proved, it is not the wind coming over the windshield beating you up, but the wind that comes up from under the sides of the fairing past the turn signals that is abusing the rider with extremely turbulent air. If you have ever put your feet on the top of your crash bars at highway speed you have some idea how well GADS will work for you. GADS mount to the fairing support bracket between inner fairing and the fairing support bracket with a virtually invisable mounting system.(Will fit older RoadGlides if using updated turnsignals and relocated upper fairing.) GADS 002 designed to fit all Ultra Road Glide models and Road Glides set up as Ultras using late model Vented Lower Fairings and late model support brackets with late model Turn Signals. MADE IN THE USA Installation Instructions View Colors

GADS002

2004 -2013 RoadGlide
GADS are created using virtually indestructible polycarbonate. GADS have a mounting system that uses the turn signal mounts to hold the deflector in place. They sit between the mounting bracket and the inner fairing, virtually invisible from the outside of the fairing. The top of the mounting flange has a hole and a notch, allowing for adjustment. The top of the flange is horizontal and sits toward the center line of the motorcycle. The notch is for the rear bolt and the wiring. Keep the wiring in the notch, do not pinch the wiring. The hole is for the front mounting stud.

Remove protective film from GADS.

Cover the front fender with a towel to avoid scratches or dings.

Pick a side to install the GADS on, then remove the nuts that hold the front turn signal on but do not remove the signal yet as there are wires that power the signal.

Pull the turn signal studs loose from the fairing but do not pull the wires out of the fairing.

Slide the hole in the front of the deflector mounting flange between the mounting bracket and the inner fairing aligning the three holes. (inner fairing, GADS, fairing support bracket)

Loosely install turn signal CAUTION: DO NOT PINCH WIRING

The notch allows for a small amount of adjustment, pivot the deflectors toward the crash bar, recheck wiring, then tighten to torque spec. do not over tighten if installing GADS002 in front of lowers, install so the ploycarbonate cannot come into contact with the paint. GADS will bend a small amount under a wind load.

Move to the other side and repeat

GADS is a small cottage industry Thank you for your support Made in the U.S.A.
Select options This product has multiple variants. The options may be chosen on the product page Details
GADS LT14 for Harley Davidson® Touring Platforms 2014 and up

$22.49

The GADS LT14 is a deflector that not only deflects the wind but also covers the brake plumbing for the front end. This deflector mounts using existing bolts. The GADS LT14 is black polycarbonate. MADE IN THE USA Installation Instructions

Add to cart Details
GADS LTTD for Harley Davidson® Touring Platform through 2013

$19.95

GADS Lower Triple Tree Deflector
GADS LTTD is a new, patented air deflector for all Road King, Electra Glide, Street Glide, and Road Glide Touring Platforms from Harley Davidson Motorcycles. Fits through 2013 Harley models. GADS LTTD redirects the air from under your Lower Trible Tree down onto your motor, helping you to enjoy your riding experience. The linear wing approach that GADS LTTD has taken assures that substantially more of the wind and turbulence flowing under the headlight and triple tree, is rerouted down onto your motor, giving you a calm and more comfortable ride. MADE IN THE USA Notice: The bolts that hold the GADS LTTD on are 1/4'x20tpi. The triple tree is pre-drilled to accept the included bolts. If there is much resistance when screwing in the bolts you probably ned to chase the threads out with a 1/4-20 tap to remove any obstruction on threads. (paint, rust, etc.) Installation Instructions View Colors

GADS LTTD

GADS Lower Triple Tree Deflector

This deflector installs to most touring platform H-D motorcycles through 2013
If you look at the back edge of your lower triple tree and see 3 little plastic plugs or holes this is where your deflector mounts The bolts that hold the the GADSLTTD on are 1/4”X20 tpi. The triple tree is pre-drilled and tapped to accept the included bolts. If there is any resistance when screwing in the bolts you need to chase the threads with a 1/4”-20 tap to remove any obstruction on the threads (paint,rust,etc.) GADS is a small cottage industry Thank you for your support Made in the U.S.A.

Select options This product has multiple variants. The options may be chosen on the product page Details